• 产品名称
  • 产品概述

    Abcam's APC/Cy7 Conjugation Kit provides a simple and quick process to conjugate your primary antibodies with APC/Cy7. APC/Cy7 is a tandem conjugate: APC (energy donor) has an excitation wavelength of 650nm and Cy7 (energy acceptor) has an emission wavelength of 774nm.

    The conjugated antibody can be used straight away in WB, ELISA, IHC, Flow Cyto etc

    Learn more about buffer compatibility, protein/secondary antibody conjugation and labelling chemistry in our FAQs.


  • 说明

    Amount and volume of antibody

    The best ratio for any new antibody reagent must be determined by experimentation but 100-150µg of IgG antibody for every 100µg of APC/Cy7 usually gives optimal results. The 150µg quantity corresponds to an Antibody:APC/Cy7 molar ratio of about 1:1.
    The volume in which the antibody is added ideally should be between 4 and 10µl.


    1. Before you add antibody to the APC/Cy7 mix, add 1µl of Modifier reagent for each 10µl of antibody to be labeled. Mix gently.
    • Remove the screw cap from the vial of APC/Cy7 mix and pipette the antibody sample (with added Modifier) directly onto the lyophilised material. Resuspend gently by withdrawing and re-dispensing the liquid once or twice using a pipette.


    • Place the cap back on the vial and leave the vial standing for 3 hours in the dark at room temperature (20-25°C). Alternatively, and sometimes more conveniently, conjugations can be set up and left overnight, as the longer incubation time has no negative effect on the conjugate.


    • After incubating for 3 hours (or more), add 1µl of Quencher  reagent for every 10µl of antibody used. The conjugate can be used after 30 minutes.


    Storage of conjugates

    For any new conjugate, initial storage at 4°C is recommended. A preservative may be desirable for long-term storage. Other storage conditions (e.g. frozen at -70°C or stored at -20°C with 50% glycerol) may also be satisfactory. The best conditions for any particular conjugate must be determined by experimentation.

    Ideally, the antibody to be labeled should be in 10-50mM amine-free buffer pH range 6.5 to 8.5. However, many buffers outside these limits of concentration and pH can be accommodated. Modest concentrations of Tris buffer are also tolerated.

    Amine-free buffers, including MES, MOPS, HEPES and phosphate are compatible if they are in the concentration range 10-50mM and have pH values in the range 6.5-8.5, as the addition of Modifier provides the conditions necessary for efficient conjugation. Common non-buffering salts (e.g. sodium chloride), chelating agents (e.g. EDTA), and sugars may be present, as they have no effect on conjugation efficiency. Azide (0.02-0.1%) has little or no effect. If the amine-free buffer is relatively concentrated and outside the pH range 6.6-8.5 you may need to add more Modifier for each 10µl of antibody. Excess Modifier is provided so that you can check the pH of the buffer after the addition of the modifier. Ideally the pH should be around 7.3-7.6, though efficient conjugation occurs anywhere between pH 6.8 and 7.8. Avoid buffer components that are nucleophilic, as these may react with the kit chemicals. If your buffer contains primary amines (e.g. amino acids, ethanolamine) and/or thiols (e.g. mercaptoethanol, DTT), you should consider using our Concentration and Purification Kits (ab102778 or ab102784). (Note: Unusually, for an amine, Tris has little effect on conjugation efficiency as long as the concentration is 20mM or less).



    Labeling of the antibody will not work if the conjugation blocks the active paratope. This situation is rare.


    This material is also subject to proprietary rights of GE Healthcare Bio-Sciences Corp. and Carnegie Mellon University and made and sold under License from GE Healthcare Bio-Sciences Corp. This product is licensed for sale only for research. It is NOT licensed for any other use. There is no implied license hereunder for any commercial use.


    COMMERCIAL USE shall include:

    1. Sale, lease, license or other transfer of the mater


    The antibody to be labelled should be purified, in an appropriate buffer for conjugation and at a suitable concentration, as described in the protocol booklet. If not, consider using our antibody purification and concentration kits.

  • 经测试应用
    适用于: Conjugationmore details



Our Abpromise guarantee covers the use of ab102859 in the following tested applications.

The application notes include recommended starting dilutions; optimal dilutions/concentrations should be determined by the end user.

应用 Ab评论 说明
Conjugation Use at an assay dependent dilution.


  • This illustration demonstrates a general procedure and will slightly vary dependent on the conjugate used.



ab102859 has not yet been referenced specifically in any publications.


Thank you for your patience.

I have received an update from the lab and unfortunately they are unable to conjugate this antibody with fluorophores. Therefore the conjugation kits we provide would be the most suitable alternative. If you have...

Read More

Thank you for your patience.

I am still waiting for the lab to confirm whether it will be possible to conjugate the clone MMA (Anti-CD15 antibody) to APC, APC/Cy7 or Alexa fluor 647.

We have a number of conjugation kits that enabl...

Read More

Thank you for your enquiry. I am sorry to confirm that we do not provide a customer conjugation service. We do have several conjugation kits available with different flourochromes. We have many available, including some for APC-Cy7 conj...

Read More