• 产品名称
  • 产品概述

    Abcan's APC/Cy5.5 Conjugation Kit provides a simple and quick process to conjugate your primary antibodies with APC/Cy5.5. APC/Cy5.5 is a tandem conjugate: APC (energy donor) has an excitation wavelength of 650nm and Cy5.5 (energy acceptor) has an emission wavelength of 694nm.

    The conjugated antibody can be used straight away in WB, ELISA, IHC etc

    Learn more about buffer compatibility, protein/secondary antibody conjugation and labelling chemistry in our FAQs.


  • 说明

    Amount and volume of antibody

    The best ratio for any new antibody reagent must be determined by experimentation but 100-150µg of IgG antibody for every 100µg of APC/Cy5.5 usually gives optimal results. The 150µg quantity corresponds to an Antibody:APC/Cy5.5 molar ratio of about 1:1.
    The volume in which the antibody is added ideally should be between 40 and 100µl.


    1. Before you add antibody to the APC/Cy5.5 mix, add 1µl of Modifier reagent for each 10µl of antibody to be labeled. Mix gently.
    • Remove the screw cap from the vial of APC/Cy5.5 mix and pipette the antibody sample (with added Modifier) directly onto the lyophilised material. Resuspend gently by withdrawing and re-dispensing the liquid once or twice using a pipette.


    • Place the cap back on the vial and leave the vial standing for 3 hours in the dark at room temperature (20-25°C). Alternatively, and sometimes more conveniently, conjugations can be set up and left overnight, as the longer incubation time has no negative effect on the conjugate.


    • After incubating for 3 hours (or more), add 1µl of Quencher  reagent for every 10µl of antibody used. The conjugate can be used after 30 minutes.


    Storage of conjugates

    For any new conjugate, initial storage at 4°C is recommended. A preservative may be desirable for long-term storage. Other storage conditions (e.g. frozen at -70°C or stored at -20°C with 50% glycerol) may also be satisfactory. The best conditions for any particular conjugate must be determined by experimentation.

    Ideally, the antibody to be labeled should be in 10-50mM amine-free buffer pH range 6.5 to 8.5. However, many buffers outside these limits of concentration and pH can be accommodated. Modest concentrations of Tris buffer are also tolerated.

    Amine-free buffers, including MES, MOPS, HEPES and phosphate are compatible if they are in the concentration range 10-50mM and have pH values in the range 6.5-8.5, as the addition of Modifier provides the conditions necessary for efficient conjugation. Common non-buffering salts (e.g. sodium chloride), chelating agents (e.g. EDTA), and sugars may be present, as they have no effect on conjugation efficiency. Azide (0.02-0.1%) has little or no effect. If the amine-free buffer is relatively concentrated and outside the pH range 6.6-8.5 you may need to add more Modifier for each 10µl of antibody. Excess Modifier is provided so that you can check the pH of the buffer after the addition of the modifier. Ideally the pH should be around 7.3-7.6, though efficient conjugation occurs anywhere between pH 6.8 and 7.8. Avoid buffer components that are nucleophilic, as these may react with  chemicals. If your buffer contains primary amines (e.g. amino acids, ethanolamine) and/or thiols (e.g. mercaptoethanol, DTT), you should consider using our Concentration and Purification Kits (ab102778 or ab102784). (Note: Unusually, for an amine, Tris has little effect on conjugation efficiency as long as the concentration is 20mM or less).



    Labeling of the antibody will not work if the conjugation blocks the active paratope. This situation is rare.


    The antibody to be labelled should be purified, in an appropriate buffer for conjugation and at a suitable concentration, as described in the protocol booklet. If not, consider using our antibody purification and concentration kits.

  • 经测试应用
    适用于: Conjugationmore details



Our Abpromise guarantee covers the use of ab102855 in the following tested applications.

The application notes include recommended starting dilutions; optimal dilutions/concentrations should be determined by the end user.

应用 Ab评论 说明
Conjugation Use at an assay dependent dilution.


  • This illustration demonstrates a general procedure and will slightly vary dependent on the conjugate used.



ab102855 has not yet been referenced specifically in any publications.


Thank you for your enquiry. We do have the the following APCCy5.5 conjugation kits available: ab102853 EasyLink APC/Cy5.5® Conjugation Kit (1x100 µg APC/Cy5.5®) Click here (or use the following: https://www.abcam.com/index.html?datasheet=102853).   ab1...

Read More

This may be possible by performing a time course of conjugation. One could set up the conjugation and then remove small samples of the conjugate over the desired time course. The removed samples should be quenched immediately and then stored either on ...

Read More